The real surprise is the excellent analog inputs especially the phono preamp! An unusual option for a receiver of this era. Vinyl sounds terrific. Very well balanced, somewhat narrower soundstage, and has no trouble driving 8 ohm amd 4 ohm loads at the same time. Driving my KEF The looks are classic Yamaha, I love the golden coloured VFD and combination of analog dials and digital controls.
The front facing av connections are nice added feature and somewhat striking in their dead center placement. No issues connect this to my modern 4k Smart TV using optical audio outputs. Press again to restore the audio output to the previous volume level. Page Connections Before connecting components CAUTION Do not connect this unit or other components to the mains power until all connections between the components have been completed.
Page Connecting The Antennas inch reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. I Speaker placement Refer to the following diagram when you place the speakers. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.
Page Subwoofer Jack A rear center speaker can be connected to these terminals. Use d to move to the next setting.
Page Setting The Unit To Match Your Speaker System Setting the unit to match your speaker system Follow the instructions below to set the amplifier output to match the size of your room and speakers.
Page Night Listening Mode Start playback or select a broadcast station on the source component. Refer to the operation instructions for the component. Adjust the volume to the desired level. The volume level is displayed digitally. You can select the type of input signals you wish to use. For details about each program, see pages 28 — It creates virtual speakers to reproduce a natural sound field. Page Digital Sound Field Processing Dsp The traditional stereo system that uses only two speakers is not capable of recreating a realistic sound field.
The processor controls the strength and delay time of the signals output from the four effect speakers to localize the virtual sound sources and fully encompass the listener. It recreates comprehensive movie sound design in your audio room. Page Tuning There are 2 methods of tuning; automatic and manual. Automatic tuning is effective when station signals are strong and there is no interference. This function enables the unit to automatically tune in to FM stations with strong signals, and to store up to 40 8 stations x 5 groups of those stations in order.
See page 32 for tuning instructions. Page Selecting A Preset Station Selecting a preset station You can recall any desired station simply by selecting the preset station number under which it was stored.
Page Sleep Timer Use this feature to automatically set this unit in standby mode after the amount of time you have set. The sleep timer is useful when you are going to sleep while this unit is playing or recording a source. Page Automatic Preset Tuning Automatic preset tuning You can use the automatic preset tuning feature to store up to 40 FM stations with strong signals A1 to E8: 8 preset station numbers in each of the 5 preset station groups in order.
You can then recall any preset station easily by selecting the preset station number. A1:FM XM is broadcast in superior digital audio from coast to coast. From rock to reggae, from classical to hip hop, XM has something for every music fan. The following display appears in the OSD. Refer to the operating instructions for those components.
Caution The DTS signal is a digital bitstream. Attempting to digitally record the DTS bitstream will result in noise being recorded. Page Advanced Sound Configurations Advanced sound configurations Changing sound field parameter settings You can enjoy good quality sound with the initial factory settings.
Although you do not have to change the initial factory settings, you can change some of the parameters to better suit the input source or your listening room. Each sound field program has some parameters defining the characteristics of the program. To change sound field parameter settings, see page 61 for details.
Sound field parameter INIT. DLY Initial delay. Presence, surround, and surround back sound field initial delay. Changes the apparent distance from the source sound by adjusting the delay between the direct sound and the P. DLY first reflection heard by the listener. Presence, surround, and surround back room size. Adjusts the apparent size of the surround sound field.
The larger the value, the larger the surround sound field becomes. As the P. Page 69 Sound field parameter REV. TIME Reverberation time. Adjusts the amount of time taken for the dense, subsequent reverberation sound to decay by 60 dB at 1 kHz. This changes the apparent size of the acoustic environment over an extremely wide range. Page Selecting Decoders Advanced sound configurations Sound field parameter 2ch Stereo 2-channel stereo direct. Bypasses the decoders and the DSP processors of this unit for pure hi-fi stereo sound when playing 2-channel analog sources.
Sends stereo signals to the surround speakers as well as the front speakers for a wraparound effect. Change the initial settings indicated in bold under each parameter to reflect the needs of your listening environment. Page 77 Woofer section of a speaker is 16 cm 6. Ideally, each speaker should be the same distance from the main listening position.
However, this is not possible in most home situations. Press one of the input selector buttons A on the remote control to select the input source you want to change the name of.
Use this feature to set the volume level of Zone 2 when the power of this unit is turned on. Choices: Off, — To control your TV or other components, you must set up the appropriate remote control code for each input source see page You must set the appropriate remote control code for each input source in advance see page The following table shows the function of each control button used to control other components assigned to each input selector button.
Press one of the input selector buttons A on the remote control to select the input area you want to set up. Page Resetting All Remote Control Codes Remote control features Resetting all remote control codes Use this feature to clear all the remote control codes previously set and reset all of them to the initial factory settings.
Page Using Multi-Zone Configuration Yamaha dealer or service center about the Zone 2 connections that best meet your requirements.
0コメント